Removing half wall on stairs and replace with rail

Replacing a stair banister is a project that you can tackle on your own once you learn about each part, what its function is, and how they all work together.

If your banister is damaged, worn, or you just want an updated look, replacing it is the best option. Follow these steps to get started, and transform the look and feel of your stairway. Go to a home improvement store and choose what kind of banister you would like. Updating your current banister from a wood to a wrought iron one or vice versa can give your home a striking new appearance. Measure the size of your existing banister to get a feel for how large your new banister will need to be.

In most cases, you will have to cut the banister to size so it is a good idea to buy a little more than you need. Remove anything delicate or easily breakable such as ornamental plates, clocks or small furniture from the area around the banister in case pieces fall as you remove them. If you're worried about falling pieces chipping your flooring, put a heavy blanket or tarp on the floor.

Make sure anyone else living in the house especially small children knows to stay out of the area while you're working. Now that you've secured the work area, use a chisel to remove the existing stair banister, beginning with the handrail.

If you are planning on reusing the spindles, remove them very carefully be sure not to damage them. This is a good option if you want to save money, as long as the spindles are in good shape and match the new handrail. Remove the existing newel post along with the screws or dowels holding it in place.

Replacing Half Wall with Wrought Iron Balusters

Clean any splintered wood if the dowels are broken. Put your new newel post in place to ensure a fit and use dowels, screws, glue and rail bolts to firmly secure it.

For the best hold, you will want to remove the subfloor, anchor the newel post to the floor joists below, and then attach it to the stair stringer. It is very important to ensure that the post is securely attached, as it is the cornerstone of the whole stair railing. If you have other people living in your house, make sure everyone knows not to touch it until you've finished securing it or the glue has dried.

Drill a hole into the side of the newel post at the level where the handrail will go and insert a long screw. Use a drill to drill screw holes in your wall and attach the handrail brackets to the wall. Place the rail on the brackets working your way from top to bottom, placing the railing on the spindles as you go down.

Replacing an old stair banister is important because it is more than just a decoration, it is also an important safety feature. You are not only saving money by following these nine steps, but are also preventing future injuries!

We welcome your comments and suggestions. All information is provided "AS IS. All rights reserved. You may staffy puppies for sale surrey link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here.

Toggle navigation Login Register How-Tos. Remove and Replace an Old Stair Banister. Written by Niki Team Hampton. Reviewed by Gabriel Connor Salter. What You'll Need. Railing System or individual banister pieces railing, newel post, spindles.

Build A Stair Railing For A Half Wall

Carpenters glue.We finished our basement a couple of years ago, and turned part of it into a work out room. If you're looking for an easy DIY accent wall that has a large impact and offers functionality, this I immediately knew Editor's Note: This mask is not a N95 mask. It is meant to be used for general protection from By now, you've probably figured out we're all about spray paint. This isn't your run of the mill staircase makeover, I wanted to achieve a rustic unfinished look for For my staircase makeover, I removed the ugly, old, worn carpet and revamped the stair treads with One of the areas that has remained unfinished in my condo, is the basement staircase.

While the I really wanted to have a gallery wall going up the stairs. It is the first thing you see when you I love to paint and I've been practicing a lot so I have a bunch of canvases that need framing.

Hi everyone! These reusable cloth wipes are easy to make. I am definitely a beginning seamstress, and I made If you're looking for a fun project, especially one that can help you keep kids busy inside these As we head into summer, make yourself an easy and affordable outdoor bar area! Whether its placed Are you embarrassed by your dated master bathroom.

I sure was.Some forums can only be seen by registered members. We are considering removing existing half wall and replacing it with railings and trying to determine costs for DIY or hiring a contractor. The half wall is in 2 segments about 15 feet x 10 feet and it's in a L shape so total of 20 ft of half wall needs to be replaced with railings. I agree, and you wouldn't want it on your conscious if you didn't do it right.

Stairs are no joke to county code and an inspector will likely pick up on the fact this was an addition to the home and check. I've seen county inspectors refuse to issue certificates of occupancy or revoke because of something wrong with stairs. They have to be perfect. True story that is ongoing as we speak in coastal NC. Please register to post and access all features of our very popular forum. It is free and quick. Additional giveaways are planned.

Detailed information about all U. Posting Quick Reply - Please Wait. Similar Threads Cost to install indoor stair railingsLong Island, 4 replies Can you replace half a roof for now and the other half later? New stair railings, etc.

Weekend Jan 20-22 2017

Follow City-Data. Twitter :. Cost to replace half wall with railings code, interior, standard. User Name. Remember Me. View detailed profile Advanced or search site with.

Advertisements We are considering removing existing half wall and replacing it with railings and trying to determine costs for DIY or hiring a contractor.

Location: D. City-Data Forum Message. Cancel Changes. Quick Reply.Based in southwestern Pennsylvania, Michelle Hickman has written since on an array of topics including lifestyle, writing instruction and financial services. Stairs can make you feel boxed in if you have two full walls on both sides.

You can tear down part of the wall to open up the stairway space. To prevent anyone from falling off the stairs, you can add stair posts and a handrail. Before you begin tearing down any wall, check the wall to ensure it is not a load-bearing wall, which can cause serious structural damages to your house if removed improperly. Have a building engineer or certified contractor check the wall and tell you the best way to add load-bearing support if needed.

Place drop cloths around the wall you are going to tear down. Lay sheets of plastic on furniture too big and heavy to move from the room so it doesn't get dirty. Close doors into rooms you don't have to enter. Cover open entrances with plastic by taping the plastic's top edge to the wall with masking tape so you can still pass through to get supplies.

Turn off the electricity and shut off the water pipes. Remove outlet covers for sockets and light switches from the wall. Punch a hole in the wall with a hammer. Pull down the drywall with your hands and the crowbar. If you find water pipes, you will need to cap the pipe and reroute the water line. Pull out wiring with your hands to reroute the electricity lines through another wall. Lay the tape measure on the step and up against the wood stud. Place a mark on the stud for the level of the step.

Place a 2 inch by 4 inch board along the studs, lining up to the marks at an angle going up.

removing half wall on stairs and replace with rail

Draw a slanted line on the front facing of each stud. Cut the studs along the slanted mark with a jigsaw tool. Pull the top of the studs from the top plate wood. Cut the top plate wood flush to the other wall if it extends through. Place a diagonal cut in the top plate so a crowbar can be wedged between the two pieces. Yank down the top plate and use the hammer to remove nails sticking out from the ceiling. Place the 2 inch by 4 inch board along the bottom cut studs.

Nail down the board. You can place the bottom decorative stair rail against the 2-inch by 4-inch board so that you will not have a lower gap between the bottom rail and the step. You also do not have to drill holes into the existing steps for the stair posts, shortening each step's length.

Cut drywall to fit along the lower section of wall.When we bought this house a couple of years ago, the stairwell was open on one side with a half wall, nothing else. As much fun as our kids had sliding down this area, it looked incomplete and posed a safety problem for the baby now racing up the steps faster than we could chase her.

How to Cut a Wall Down to Install Stair Posts and Handrails

Our solution: Build a Newel Post and close in that space with a simple handrail and homemade balusters. Check out the build video below and be sure to hammer that thumbs up button!! I sent the post through as well, a few passes brought it down to 3 inches. It just l ooked right. At the bandsaw, all the rough Oak that we planed down needed to be ripped to a rough width for the Balusters.

Time to rip down some plywood! To add durability and some visual dimension, I chose to wrap the bottom portion and corners of the post with solid Oak, taking my lumber over to the table saw and while there, creating a miter that I would use for the trim.

These 4 corner strips I glued together first, using these handy miter spring clamps for a perfect, sturdy seam. Once they were dry it took very little time to add them onto the post, using the same method as before. After each corner was applied, I took a minute to add a small piece of horizontal trim with fast acting Titebond adhesive to break up the look of the post.

It added a nice touch. I actually made 2 Newel posts simultaneously, as our half wall needed a shorter one at the top to accommodate the railing.

We needed a decorative piece for the top of our post, and I figured something up using trim and a cap for the very top. It was a puckering experience to cut miters on such a small piece, but we made it through with all appendages attached. Some glue and brad nails set it in place and after spackling the holes and sanding the whole thing up to grit, we were ready to move on. Then, for the first time on this project, we went over to the router table to add a chamfer on all four sides of each Spindle to create a finished look.

We only wanted this chamfer detail in the middle of each Spindle, so I first put up a stop block on the router table to ensure accuracy and make things easier for the job at hand. Sanding everything down was a breath of fresh air with my supermax drum sander.

Not a necessity to have in your shop, but pretty amazing if you can swing it. And…Ready for finish. We used General Finishes Shaker Maple, Our default setting for staining the Balusters and decided to paint the Newel posts for a unique and fresh look.

Bonus, it was also easier to cover up the nail holes that ended up on there during installation. I know I talk about this Fuji q5 Platinum Sprayer a lot, but let me just say again….

We were now ready to move the project inside for installation. First order of business was to remove the carpet and cut a hole through the floor, where the Newel Post would slide in and be secured from below. We also needed to take a minute and remove the old half wall trim and install our new oak piece that was seen earlier in the project.

The ends were chamfered to accommodate the inside trim measurement of the Newel post, which was why it was important to address this install before securing the post downstairs.

The wall was not square so we ended up having to shim it and caulk later. The half newel post where the railing begins at the top was adhered to the wall with construction adhesive and 6 inch structural screws as well, but it was not necessary to screw from below.

Ever so carefully I cut the handrail to length and installed it between the Newel posts using countersunk holes, screws, and help from The Wife. Unfortunately the decorative horizontal trim got in the way and I ended up having to notch out the railing so it would sit at the appropriate height.I am not sure why but finding someone to replace my half wall with balusters was one of the harder task so far.

For some reason, I have the hardest time finding the right people to do the job. Can anyone else relate? Although you can find me doing many home improvement projects, I was not confident enough to tackle this one. I was mostly concerned with the banister being stable.

Staining existing railing to match new rail. Before: That top base board of the half wall was used as the bottom base that holds the iron posts.

How to Remove Wood Stair Railing

How efficient! After: The base board moved to the bottom and a support post installed. It was explained that it is federal regulation to install a deep seated post for ever so many balusters or feet. This supports the weight and length of the railing. Thanks for your response.

removing half wall on stairs and replace with rail

The railings look lovely — I just need to find someone in the Tampa, FL area to do this job! Hi Lisa!!! Thank you for leaving me a comment. I get this question all the time.

I do not remember the color but I do have the Home Depot barcode and paint info. It is behr paint. Your railing looks beautiful. I am in Dallas and looking to do something similar. Would you mind telling us how many linear feet of railing that ended up being?

Hi Lisa. I thought I responded to this weeks ago. Anyway, thank you for stopping by and the warm comment. Our railing is apprx 13ft. I watch as the pieced together to rails to make this whole piece. Hope this helps. Have a good weekend. That looks amazing! I need to find someone to do this in Utah.Put on safety glasses and work gloves, and then cut around the seam of the wall where it connects to the side wall.

This cuts through the drywall tape, making for a neater repair. Use pry bars to remove the trim. The nails in the top plate will probably be pretty tough.

removing half wall on stairs and replace with rail

An old-time nail puller is the best way to remove stubborn nails. Next, go to work with the reciprocating saw. Cut through the top plate on either side of a vertical support stud. Remove the chunk of the 2-by-4 top plate and use a pry bar to remove the two sections of the top plate. Cut along the base of the wall, horizontally, with the reciprocating saw.

Once done, have a friend help you lift and remove the wall. Pry the base plate from the floor using a crowbar. Vacuum up the mess using the shop vacuum. Smooth the edges of the cutout area on your permanent wall a drywall rasp. Cut and install a patch using a power drill and drywall screws. Cover the joints of the patch with drywall tape. Throw some drywall mud in a mud bucket and cover up the area using a drywall knife.

Privacy Policy. Home Design Decorating Design Taking down a half wall is an easy way to create more open space. Pinterest Facebook Twitter Email. Related To: How To Walls. Want more space in your favorite room? Take down a half wall with these easy steps. Materials and Tools:. Plan carefully and feel at ease making major changes to the footprint of your home.

Create a Geometric Focal Wall With Trim A bold paint color and simple molding turn a bare wall into a stunning, graphic focal point. Expanding a Window to a Door Add an extra opening to your home by converting a window to a door.

removing half wall on stairs and replace with rail

Demolition: Removing Walls Follow these guidelines for a safe takedown. How to Safely Remove Kitchen Cabinets Learn how to safely remove your old cabinetry to get ready for your new kitchen remodel. How to Create Paneled Walls Give your walls a two-toned panel effect with these easy step-by-step instructions.

Adapted from his book Walls that Wow. Load More. Nate and Jeremiah: Save My House 6am 5c. Nate and Jeremiah: Save My House 7am 6c.


comments

Leave a Reply

Your email address will not be published. Required fields are marked *